Power Viewer Mobile 2
Enables mobile RF power measurement with up to 4 R&S® NRP series Power Sensors
Rohde & Schwarz GmbH & Co. KG · com.rohdeschwarz.android.nrpdriver
UpdatedNov 10, 2025
PublishedOct 23, 2020
Packagecom.rohdeschwarz.android.nrpdriver
MD5386a7ee7f8733f09534f04bc2916e75e
SHA1 (signer)62:CA:31:2D:E2:CF:EC:CE:84:BB:00:B9:F1:E3:C4:64:4A:13:61:46
Signed byOU=1GP3, O=Rohde & Schwarz GmbH & Co.KG, L=Munich, C=DE
Malware scanTRUSTED
Contact[email protected]
Privacy policyView
What's new
Now supporting new API level and new sensor models
Description
With the new Power Viewer Mobile 2 App you are able to use all Rohde&Schwarz NRP series RF Power Sensor with your Android smartphone or tablet.
Requirements:
o R&S®NRP Power Sensor
o R&S®NRP-Zxx Power Sensor
o Device with Android 5.0 or higher
o USB-OTG adapter cable (If the sensors should be used via USB)
o Network connection with PoE (If Network Sensors should be used)
Optionally a USB hub can be used to connect more than one USB sensor to the Android device.
Supported Features:
o Continuous average mode
o Trace mode
o Up to four sensors simultaneously
o Support for Measurement over Network (with R&S®NRP-xxXN power sensors)
o Flexible user interface
o Extensive settings for the supported measurement modes
Important:
This app depends on a working USB host (USB – On The Go) controller built into your device. Some smartphones block high-power USB devices. In this case only the sensors with low supply power requirements will work, or the use of a self-powered USB hub is necessary.
The Trace Measure mode is only available with Sensors with support of this mode. If a Sensor doesn’t support this mode, nothing will be shown if switching to the Trace mode.
Warning:
Connecting an R&S®NRP power sensor to the USB port of your Android device will drain your battery regardless whether this app is active or not. Make sure to disconnect the power sensor whenever not in use.
Requirements:
o R&S®NRP Power Sensor
o R&S®NRP-Zxx Power Sensor
o Device with Android 5.0 or higher
o USB-OTG adapter cable (If the sensors should be used via USB)
o Network connection with PoE (If Network Sensors should be used)
Optionally a USB hub can be used to connect more than one USB sensor to the Android device.
Supported Features:
o Continuous average mode
o Trace mode
o Up to four sensors simultaneously
o Support for Measurement over Network (with R&S®NRP-xxXN power sensors)
o Flexible user interface
o Extensive settings for the supported measurement modes
Important:
This app depends on a working USB host (USB – On The Go) controller built into your device. Some smartphones block high-power USB devices. In this case only the sensors with low supply power requirements will work, or the use of a self-powered USB hub is necessary.
The Trace Measure mode is only available with Sensors with support of this mode. If a Sensor doesn’t support this mode, nothing will be shown if switching to the Trace mode.
Warning:
Connecting an R&S®NRP power sensor to the USB port of your Android device will drain your battery regardless whether this app is active or not. Make sure to disconnect the power sensor whenever not in use.
Required features
- Faketouch android.hardware.faketouch
- Usb Host android.hardware.usb.host
- Wifi android.hardware.wifi
Permissions (4)
Power Viewer Mobile 2 requests the following Android permissions:
- Access Wifi State android.permission.ACCESS_WIFI_STATE
- Change Wifi Multicast State android.permission.CHANGE_WIFI_MULTICAST_STATE
- Internet android.permission.INTERNET
- Wake Lock android.permission.WAKE_LOCK
