MHD F+G Series APK

Version version 1.20 - com.mhd.flasher.fseries
flasher,fseries,auto,vehicles,series

The MHD Flasher F+G Series is a complete flash tuning app for your BMW

APP Information

Download Version version 1.20 (48)
Apk Size44.09 MB
App DeveloperMHD Tuning UG
Malware CheckTRUSTED
Install on Android3.2.x and up
App Packagecom.mhd.flasher.fseries.apk
MD5e0458ce4b3147f3b1788f3225c202d35
Rate5
Website http://mhdtuning.com

Download MHD F+G Series version 1.20 APK

App Description

MHD F+G Series is flasher,fseries,auto,vehicles,series, content rating is Everyone (PEGI-3). This app is rated 5 by 1 users who are using this app. To know more about the company/developer, visit MHD Tuning UG website who developed it. com.mhd.flasher.fseries.apk apps can be downloaded and installed on Android 3.2.x and higher Android devices. The Latest Version of version 1.20 Available for download. Download the app using your favorite browser and click Install to install the application. Please note that we provide both basic and pure APK files and faster download speeds than APK Mirror. This app APK has been downloaded 154+ times on store. You can also download com.mhd.flasher.fseries APK and run it with the popular Android Emulators.

The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
---------------------------------------------
Full OBD Flashing: 
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. 
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:

N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM)
- Stage 2+ (up to 430HP/630NM) 
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%

N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM)
- Stage 2 (up to 370HP/580NM)
- Stage 2+ (up to 400HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%

S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM)
- Stage 2 (up to 560HP/780NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%

B58:
- Stage 1 (up to 420HP/580NM)
- Stage 2 (up to 470HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! 

These are some of the available monitors:

- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…

MHD exclusive advanced monitor:

- Timing Corrections per Cylinder
- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
---------------------------------------------
These flash options can be applied to any map directly through the app:

- Exhaust Burble (duration & aggressiveness, min speed, min rpm)
- N20 Map Sensor (on N55)
- Remove top speed limiter (Vmax)
- Cold start noise reduction
- Exhaust flap open in sport mode
- Limit power per gear
- XHP TCU flash support (optimizied OTS maps)
- Sport cooling mode for increased water / air intercooler cooling (B58 only)
---------------------------------------------
Supported Cars: 

M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016 
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015 
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018

M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019 

M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -

114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018

X-Drive is supported on all cars.
All performance power kit cars are supported.

Check out our homepage / user manual for more information and recommended modifications for each stage.

The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
---------------------------------------------
Full OBD Flashing: 
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. 
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:

N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM)
- Stage 2+ (up to 430HP/630NM) 
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%

N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM)
- Stage 2 (up to 370HP/580NM)
- Stage 2+ (up to 400HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%

S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM)
- Stage 2 (up to 560HP/780NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%

B58:
- Stage 1 (up to 420HP/580NM)
- Stage 2 (up to 470HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! 

These are some of the available monitors:

- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…

MHD exclusive advanced monitor:

- Timing Corrections per Cylinder
- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
---------------------------------------------
These flash options can be applied to any map directly through the app:

- Exhaust Burble (duration & aggressiveness, min speed, min rpm)
- N20 Map Sensor (on N55)
- Remove top speed limiter (Vmax)
- Cold start noise reduction
- Exhaust flap open in sport mode
- Limit power per gear
- XHP TCU flash support (optimizied OTS maps)
- Sport cooling mode for increased water / air intercooler cooling (B58 only)
---------------------------------------------
Supported Cars: 

M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016 
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015 
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018

M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019 

M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -

114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018

X-Drive is supported on all cars.
All performance power kit cars are supported.

Check out our homepage / user manual for more information and recommended modifications for each stage. 

App ChangeLog

App Screens

MHD F+G Series App Screen 1MHD F+G Series App Screen 2

Older Versions

More Android Apps to Consider

f

Google Play Reviews

  1. Sean Kinzer-avatar

    Sean Kinzer

    I can't say enough about this tuning app and it's benefits. Especially with the wireless adapter. Love everything about it. I can't wait to move to my next vehicle upgrade and do more

  2. Trevor Forrest-avatar

    Trevor Forrest

    Great app. Very versatile and stable. Lots of options and development. Impatiently waiting for full flex fuel map. Already have their flex fuel sensor installed. Hurry up and release it already!! Give me my full flex fuel! 🤣 Edit 8/14/21: YAY FLEXFUEL IS HERE! And multimap quick switch!? But documentation neds to be updated. Not 100% on how it works or why multimap can't allow e85 or e30 maps if flexfuel is enabled...

  3. Brian Brooks-avatar

    Brian Brooks

    The tune is great, super smooth and really powerful. It's awesome to be able to easily load a tune at home. I've had tunes loaded by shops on other cars and it meant spending hours in their waiting room while they fumbled around figuring out software and talking to the tuning company. This took me about 5 minutes of actual work and 40 minutes of wait time, at home, where I could have a beer and do other things. Flawless process and performance.

  4. Sultan Masud-avatar

    Sultan Masud

    Had some problems trying to get the licensing but it all worked out in the end and left me really impressed with the support for the app and how quickly they respond to concerns and questions. If you thought your Bmw was fast before stock, well you’re in for a suprise considering this changes the car completely power wise while the engine stays running butter smooth. No Problems or hiccups so far, 2014 Bmw 435i with 39k miles

  5. Andrew Salamone-avatar

    Andrew Salamone

    Super easy to use. Initial flash too 18 min with Galaxy S10+ (& bimmergeeks cable) and all other flashes since that take less than 1 min. Quick and easy to make changes and you can definitely feel the difference. 100% reccomend using this, wish I found it sooner. Make sure you get the right version of the app for your model. Update: 3/13/20 These guys are awesome. Constantly updating the app, adding new features and they listen to the community!

  6. Steven Calogero-avatar

    Steven Calogero

    Solid app..could be a bit "sexier" on the graphics. Support is incredible thanks fabian! I think it's more 4.5 then 5 only because it's not IOS compatible I had to buy this android phone to let it work. I love the logging but I wish it was easier to extract that's just me. I love the wife adapter its so fast but I do wish the logging model let you adjust the size of the icons for boost.. Intakentemps etc Would be nice for a resell capable to use on my next car like bootmod3

  7. Valvetronic Designs-avatar

    Valvetronic Designs

    Wow... What a difference this software makes on your car, complete transformation of how the power comes on. MHD has been in this game for awhile now; they were on of the first to crack the DME's on N54\55, they know what they're doing. And with all of the same features like cold start delete, burbles, and monitoring/logging at a fraction of the price compared to the competitors, it was an easy choice to go with MHD. Higly recommend.

  8. Travis Mawhir-avatar

    Travis Mawhir

    Stage 1 over stock is such a huge improvement. I was compelled to write a five star review not only because of this awesome platform and its functionality/versatility but the MHD team offers so much help and support. You can tell that they are dedicated to research and development and that they have a passion for modifying cars. I would highly recommend this company to anyone looking to tune their vehicle and rest assured you will not be left in the dark if you have questions. Great job!

  9. Jordan-avatar

    Jordan

    This is one of the best apps I've ever used. It makes tuning your BMW so easy that anyone can do it. Simply purchase an OBD cable, or the $70 MHD WiFi Adapter. The WiFi Adapter allows you to switch maps in around 20 seconds which is needed when you are running custom tunes, e-85/fueling tunes, or want to change the burble options on your exhaust. The amount of customizability is great on the app with the N55 engine! Highly recommend!

  10. Sam La-avatar

    Sam La

    So i bought the mhd wifi adaptor, plugged it in the obd, connected the wifi and used the app first time and it worked perfectly fine, flashed my f10. Took only 5-10 minutes, great. Now my problem is, whenever i try to flash again, i am able to connect to the wifi adaptor but i am unable to flash, the app says that a cable or wifi adaptor isn't detected. I tried everything from replugging, turning the wifi off/on, wiggling the adaptor but it still says unable to detect a cable or adaptor. Help!!